Mathmos Saturn lava lamp instructions
Box Contents
Saturn comes packaged in two boxes;
Box 1: Tripod Stand, R7s Bulb, Spun Base with Cable Kit, Top Cap
Box 2: Filled bottle
Position
Saturn is for indoor use only. Choose your position carefully, especially if
Saturn is to be used in public areas. Ensure that the cable can reach the
power socket location without being stretched and does not become a trip
hazard. Choose a position on a robust flat surface able to bear its weight.
Saturn operates at its best in a room between 20º C / 68º F and 24ºC / 75º F.
For best performance we recommend you keep the product away from:
- Direct sunlight to prevent fading.
- Drafts and cold places, such as an air conditioner, to prevent slow
operation and freezing.
- Hot places, such as a heater, to prevent overheating.
- cold places to prevent freezing
- hot places to prevent overheating
- Keep the cable away from heated surfaces.
OPTIONAL: The feet on the stand have Bolt / Screw slots
that allow you to fix the lamp onto a suitable surface. We
recommend you use suitable Bolts or screws (x 4 of the same
specification) for fixing the base. You must ensure the base is
positioned safely onto the floor.
Assembly
For a full visual guidance recommend you watch the video.
Box 1: (the larger box)
- Open and carefully take out the cap and the base.
- Place the lamp in position.
- Fit the bulb into the product by pushing one end in and springing it into
place between the lamp holder contacts. (diagram 1). Ensure that each
end of the bulb is sitting properly in the lamp holder.
Box 2: (the smaller box - bottle)
- Take great care removing the bottle from the box. It is both heavy and
delicate.
- Open the box by removing the tear off strip.
- Open the flaps and remove the top cardboard insert and set this aside.
- Using the handles on the side of the box, carefully lower the box so
the long side is on the floor.
- Place the cardboard insert set aside earlier in front of the box at the
opening to protect the bottle as it comes out of the box.
- Pull the bottle out of the box using the neck of the bottle and as you do
this move the bottle upright to stand it on the insert. (diagram 2)
- Slowly lift the bottle and then lower the bottle into position on the base,
ensuring that it fits neatly into the base spinning. NB. This operation
may require two people.
- Fit the cap on the top of the bottle.
Warm Up
Warm up takes between 3 to 4 hours depending on the ambient temperature.
Stalagmite shapes may form during the warm up process, these will then melt
and the lava will begin to flow. You may want to use a time clock with Saturn
so that it turns on automatically.
Operation
Saturn will operate best after it has been used four or five times. For the first
few times you may see small air bubbles in the lava. It is normal for the glass
to have small air bubbles and moulding scars.
Saturn can run for up to 12 hours once warmed up (during one operating
cycle). Please allow Saturn to fully cool before running it again.
Do not allow Saturn to overheat as this will shorten the life of the lava. If it is
overheating there will be either only one large bubble at the top of the bottle
or a lot of very small bubbles.
NB. Never move the product when it is in use or still warm, as this causes
irreparable clouding.
Replacements
When your Saturn has ended its life, it will begin to go cloudy, the colours
may fade and it will not move as well as it once did. This will happen after
approximately 2000 hours in operation. Whether your product has ended
its life or when you wish to have an alternative colour combination, visit our
website at www.mathmos.com for more information on a replacement bottle
or full product.
NB. Please on no account open the secure cap and add liquids.
Changing the Bulb
- It is essential to allow your product to cool down completely prior to
handling or maintaining the product.
- Once your product has completely cooled, carefully lift out the bottle from
the base and set down on a sturdy surface safely away from the base.
- Avoid handling the bulb with your bare hands, instead use a soft cloth or
similar.
- Fit the bulb into the product by pushing one end in and springing it into
place between the lamp holder contacts. (diagram 2).
- Ensure that each end of the bulb is sitting properly in the lamp holder.If the
bulb blows, please replace it with one of the same type and wattage. Only
fit the correct bulb, as started in the label in the base.
- Visit www.mathmos.com for more information or to purchase a
replacement bulb.
Safety
Safety
- This product carries the statutory guarantee of the country of purchase
and meets all the applicable standards requirements.
- This product is only suitable for connection to a 220 - 240V ~ 50Hz
mains supply. It must only be fitted with a 3A fuse.
- If this is to be installed in a public space then we recommend fitting it
to a RCD device.
- This fitting is a Class II, Double Insulated product and does not re
quire an Earth.
- Place the product well away from children under 14 years to prevent
breakage.
- Use this product only for its intended use as described in these
instructions. Do not use attachments not recommended by the
manufacturer.
- Do not use any other means to heat up the bottle other than the bulb
provided nor attempt to cool it down artificially.
- Do not operate the product for more than 12 hours once warmed up
(during one operating cycle).
- The liquids in the product are not dangerous and can be disposed of
normally (for details, see our online FAQ’s at www.mathmos.com). If the
liquid is swallowed by mistake, drink plenty of water. If any symptoms
appear, please visit a doctor.
- Never use this product if the bottle has been dropped as this will create
weakness; obtain a replacement bottle and dispose of the old one. If the
contents are spilled please dispose of as much liquid and lava as you can
remove, then use recommended cleaning methods for removing coloured
water and wax for whatever floor you have.
To reduce the risk of burns, electric shock, or injury:
- Unplug from mains outlet before putting on or taking off parts or before
cleaning.
- Never operate this product if it has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or if it has been
submerged in water.
- The external flexible cable of this product cannot be replaced. If the cable
is damaged, please contact Mathmos
- To disconnect, turn the switch to the off position, then remove plug from
outlet.
- Never touch the bulb if the product is switched on or if it has just been
switched off in order to avoid burning. To replace a defective bulb, unplug
the product and let it cool down sufficiently.
NB. Mathmos Ltd. cannot be made liable for damage or injury caused by
improper handling, installation or use of its products.
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.